INTERRUPTING RF 3 BELLBOYS DOMOTICA X10 S110315 Domótica:
Domótica controls x10
That it is X10? 
27,03-Euro.
It has wished sometimes a switch in a concrete place but it did not want to make works and to twist all a wall? Now it is possible with the technology of Dómotica X10 and the S110315 Switch who includes three switches independent and a attenuator to increase or to diminish the intensity of a lamp.
Its installation is as simple as to adhere it to the wall by means of the adhesive that brings built-in and already it is, does not need wiring some. It works with batteries that provide an autonomy to him for a year and has a thickness of only 7 mm. The programming of the direction of the bellboys is realized from the own pulsers.
A very interesting application is the one to locate it to the entrance of the hall and power to ignite from the door to 3 different lamps, choosing at every moment the wished atmosphere since besides igniting and extinguishing, he is able to regulate the intensity of the lights, and thus not to have to ignite by force the light of the ceiling, that but is often not adapted.
You order them transmitted by the radio frequency switch are received by the receiver of S110128 radio frequency and thence sent to the different modules from the domótico system by means of the mains of the house.
Totally compatible with all the X10 devices reason why macros programmed from the interface for PC S110210 can be executed, sending the order, for example “to lie down”, in which the curtains, the blinds can be closed, to extinguish all the lights, to leave to the light of the ignited porch and all that pressing a single button, (logically it has been due to program the macro before “to lie down”).
Engineering specifications
| Operation |
Radio frequency. |
| Frequency of the signal |
433,92 MHz<20mA |
| Exit of Radio |
<5833u V/M @ 3 ms |
| Rank of RF |
30 mts. in open field. |
| Temperature |
-10ºC, +50ºC |
| Weight |
75 grs. (without batteries) |
| Dimensions |
11,4 xs 7 xs 2.2 cm. |
Applications
By his facility of assembly and its elegant aspect, the radio frequency switch can be installed in any place where it is necessary. This discreet and flat switch is ideal to locate it in the environs of his bed to be able to close the blinds before lying down, igniting the coffee pot when he awakes by the mornings or to ignite the heater of the bathroom before rising. He allows to his installation in surroundings for physical handicappeds or people of outpost age and in any installation of Dómotica
Operation
By defect the radio frequency switch comes formed with the code of house “A”. The first button button comes with the code of device 1, following the 2 and thus until the 3. I complete button serves to regulate the intensity of the lights.
It presses and it leaves pressed first button ON. The red LED will blink, 3 seconds later the LED will show the present configuration: 1 blinking for the code of house To, 2 blinkings for the B… 16 for the P.
It loosen to the button superior.
It presses and it loosen to the button superior ON I number of times corresponding to the wished Code of House. 1 time stops To, 2 for B, etc. The LED will blink with each pulsation. IMPORTANT: It leaves pressed the button in completes pressure, and 3 seconds later the red LED will show the new configuration. If it does not follow the programming sequence, the LED will remain ignition during 1 second and it will not change the previous configuration.
Whenever a new code of device is programmed, this button talks about exclusively there superior, being the code of the other two consecutive pulsers to this. Thus, if program like code of device for the first button number 5, the other bellboys will be codes 6 and 7.
It presses and it leaves pressed first button OFF. The LED will blink 1 time. 3 seconds later, the LED will show the present configuration: 1 blinking for code 1, 2 blinkings for the 2… 16 blinkings for code 16.
It loosen to the button superior OFF.
It presses and it loosen to the button superior OFF I number of times corresponding to the Code of Device that wishes to program. IMPORTANT: It leaves pressed the button in completes pressure: 3 seconds later the red LED will show the new configuration. If it does not follow the programming sequence, the LED will be ignition during 1 second and it would not change the previous configuration.
It abra the compartment of the battery and places a battery type CR2032, considering the polarity of the same. IT DOES NOT THROW THE BATTERY SPENT TO THE SWEEPINGS. DEPOSITELA IN A SPECIAL CONTAINER FOR BATTERIES.
Related products
PIDALO NOW AND RECIBALO TOMORROW!
27,03-Euro.
31,35 € with IVA
|
TO SEE MAS PRODUCTS DE Mandos Domótica x10
INTERRUPTING RF 3 BELLBOYS DOMOTICA X10 S110315
Domótica: Wireless X10 switch 3 bellboys and regulator
|